Cargando…
Advances in engineering & management : selected, peer reviewed papers from the 3rd International Conference Advances in Engineering and Management (ADEM 2014), September 11-12, 2014, Drobeta Turnu-Severin, Romania /
Collection of selected, peer reviewed papers from the 3rd International Conference Advances in Engineering and Management (ADEM 2014), September 11-12, 2014, Drobeta Turnu-Severin, Romania. The 55 papers are grouped as follows: Chapter 1: Advanced Materials and Processing Technologies; Chapter 2: En...
| Clasificación: | Libro Electrónico |
|---|---|
| Autor Corporativo: | |
| Otros Autores: | , |
| Formato: | Electrónico Congresos, conferencias eBook |
| Idioma: | Inglés |
| Publicado: |
Pfäffikon (Zurich, Switzerland) :
Trans Tech Publishers,
[2015]
|
| Colección: | Advanced engineering forum ;
v. 13. |
| Temas: | |
| Acceso en línea: | Texto completo |
Tabla de Contenidos:
- Advances in Engineering & Management; Foreword, Committees and Sponsors; Table of Contents; Chapter 1: Advanced Materials and Processing Technologies; Composite Compacts of Fe/Fe3O4 Type Obtained by Mechanical Milling-Sintering-Annealing Route; Nanocrystalline/Nanosized Fe3O4 Powder Obtained by Mechanosynthesis; Green Composites Based on Kenaf Fibers; Influence of the Cutting Parameters on the Surface Roughness when Machining Hardened Steel with Ceramic and PCBN Cutting Tools; An Estimate of Thermo-Physical Changes in Hybrid Basalt/Glass Fibres Reinforced Polymer Composites
- Research of the Fe2O3 Powder Granulation Effect on BaFe12O19 Firing TemperatureEffect of Process Control Agents on the FeSiB Powder Amorphisation by Wet Mechanical Alloying; Fracture Analysis of Porous P/M Iron Based Materials; Structural and Morphological Evaluation of 25% vol. Ni/Al2O3 Nanocomposite Powders Produced by Mechanical Milling; Synthesis of Fe75Si20-xB5Mx (M=Ti, Ta or Zr) Powders by Wet Mechanical Milling; Substrate Influence on the Mechanical and Tribological Characteristics of Gold Thin Films for MEMS Applications
- The Influence of Barium Carbonate on the Tribological Characteristics of some Iron-Based Friction CompositesThe Influence of Milling Conditions on the Ni3Fe Alloyed Powder; Shape Memory NiTi and NiTiCu Alloys Obtained by Spark Plasma Sintering Process; Voids and Microstructure Evolution in Aluminium Sheets during High Deformation; Research on the Treatments at Sub-Zero Temperatures of the Sintered Steels and Hardened in Oil; Research Regarding the Influence of Copper Powders on Tensile Strength of Sintered Steels; Synthesis of the Fe-6.5% wt. Si Alloy by Mechanical Alloying
- The Tribological Behavior of some Steel Samples Prepared by Powder Metallurgy Sintered in Microwave FieldResearch Regarding the Load WIG Welding of Active Areas for Asphalt Uncovering Milling Cutter Teeth; Chapter 2: Engineering Decisions and Investigations for Mechanical Engineering; Nonstandard Mathematical Model for Fatigue Failure; 316L Metal Powder Compaction Simulation with Assisted Friction; Analytical, Numerical and Experimental Studies for SERB TEL-150 New Romanian Seismic Dampers Used in Foundation Buildings Damping System
- Computational Studies for Comparison between BRB Dampers and SERB New Romanian Dampers Performance in Damping System of High BuildingsModal Parameters Identification for some Sandwich Bars Reinforced with Fiber-Glass; Modeling the Flow in Nanostructured Sensors within Hybrid Welding Systems; Real and Simulated Mechanical Tests; Quantitative and Qualitative Methods in the Study of some Dynamic Systems; Experimental Stand Controlled by Web Interface for Data Acquisition in Punching Process; Controllable Pitch Propeller System Using the Shaft Line Energy