Cargando…

Innovative Materials : Engineering and Applications : Selected, peer reviewed papers from the 2014 International Conference on Material Engineering and Application, (ICMEA 2014), October 18-19, 2014, Hangzhou, China /

Collection of selected, peer reviewed papers from the 2014 International Conference on Material Engineering and Application, October 18-19, 2014, Hangzhou, China. The 100 papers are grouped as follows: Chapter 1: Composites, Materials Engineering and Technologies, Chapter 2: Functional Materials, Ch...

Descripción completa

Detalles Bibliográficos
Clasificación:Libro Electrónico
Autor Corporativo: International Conference on Material Engineering and Application Hangzhou, China
Otros Autores: Bhatnagar, Anil K. (Anil Kumar), 1942- (Editor )
Formato: Electrónico Congresos, conferencias eBook
Idioma:Inglés
Publicado: Zurich : Trans Tech Publications, ©2014.
Colección:Advanced materials research ; v. 1052.
Temas:
Acceso en línea:Texto completo
Tabla de Contenidos:
  • Innovative Materials: Engineering and Applications; Preface and Committees; Table of Contents; Chapter 1: Composites, Materials Engineering and Technologies; The Micro-Analysis about the Morphology and Characteristics of the Ball Mill Slag Powder; The Research of Hydrophilic Modification of PVC/PES Blended Membrane by the Additive of CA; High Speed Extrusion Rheological Behavior Analysis of Marine ABS/PC Alloy; First-Principle Studies on the Stability of AlN(0001)/NbB2(0001) Interface.
  • Mechanical Properties and Toughening Mechanisms of Multi-Walled Carbon Nanotube Reinforced Yttria-Stabilized Zirconia Composite; Energetic Studies on the B Effect on the Oxidation of [gamma]-TiAl Alloys; Carbon Fiber Reinforced SiC Matrix Composites Fabricated by Preceramic Impregnation and Pyrolysis Process Combining SiC Nano Powder Infiltration; Fabrication of TiB2/TiC Duplex Particles Reinforced Carbon Steel Matrix Surface Composite; Static Recrystallization and Texture Evolution of 316L Stainless Steel Fibers; Research in an Original Si-Mn-Mo-Nb 800MPa Dual Phase Steel with Low Carbon.
  • Effect of Copper Content on Mechanical Properties of Short Carbon Fiber Reinforced ZrC Mateix Composites; Study on the Brush Plating Technology of Super-Strength Duralumin; Polyurethane Nanocomposite Films by Using Cellulose Nanospheres as Green Nanofillers; Performance Improvement of Hydrogen Peroxide Sensor via Cadmium Doped Nickel Oxide Modifying N-Silicon Electrode; A Novel Method for Co-Simulating 1-3 Piezocomposite Performance; Different Carbon Nanotube Content and Dispersant on the Preparation of Fe3O4 / CNTs; Three-Dimensional Simulation of Nano-Composite Ceramic Tool Materials.
  • Temperature Influences on Preparation and Tribological Characteristics of Electrostatically Sprayed PTFE/PEEK Composite Coatings; Study on Preventing Springback for Nanoporous Thermal Insulating Composites; The Preparation and Research of the Electroless Plating Rare Earth Alloys; Two-Step Annealing for Solution-Based Metal Induced Crystallization of Amorphous Silicon Films; Influence of WC Content on Microstructure and Wear Resistance of (Cu-50Mo)-WC Composites; Effect of TiC Content on the Microstructure and Wear Resistance of (Cu/50W)-TiC Composite Prepared by Spark Plasma Sintering.
  • Chapter 2: Functional Materials; The Study of Electromagnetic Steel Sheet High Cycle Fatigue Properties; Stiffness and Damping Characteristics of a Wide Parabolic Film Slider Bearing Operating with Ferrofluids; Temperature Influence on the Viscoelastic Electromechanical Deformation of Dielectric Elastomer; Dielectric Strength of Flame-Retardant Reinforced Polyamides at High Temperature; A 1D Analysis of Nano Multiferroic Composites for the Novel Read Head Technology.