Cargando…
Polymer Science and Engineering : Selected, peer-reviewed papers from the 3rd International Conference on Composite Material, Polymer Science and Engineering (3rd CMPSE), October 24-25, 2019, Bangkok, Thailand /
The proceeding book contains papers from the 3rd International Conference on Composite Material, Polymer Science and Engineering (3rd CMPSE), which was held on October 24th and 25th, 2019 in Bangkok, Thailand. The main topics are technologies of materials joining; mechanical properties and mechanica...
| Clasificación: | Libro Electrónico |
|---|---|
| Autor Corporativo: | |
| Otros Autores: | |
| Formato: | Electrónico Congresos, conferencias eBook |
| Idioma: | Inglés |
| Publicado: |
Switzerland :
Trans Tech Publications Ltd,
[2020]
|
| Colección: | Key engineering materials ;
v. 858. |
| Temas: | |
| Acceso en línea: | Texto completo Texto completo |
Tabla de Contenidos:
- Intro
- Polymer Science and Engineering
- Preface
- Table of Contents
- Chapter 1: Joining Technologies
- Ultrasonic Welding of Glass Fiber Reinforced PP Thermoplastic Composites: An Investigation of the Outer Layer Orientation and the Fiber Volume Fraction
- Rate-Dependent Material Properties of Adhesively Bonded Joints
- Must Have or Nice to Have?
- Effect of Interface Geometry on Strength of Single Lap Adhesive Joint of Sisal-Glass/Epoxy Laminates
- Effect of Friction Stir Forming Process Parameters on Mechanical Interlock between A5083Alloy and Ultra-Thin Stainless Steel Strands
- Alleviation of Stress Concentration with Rivet-Like Joints Fabricated by Friction-Stir Forming
- Chapter 2: Mechanical Properties and Mechanical Testing
- Mechanical Properties of Hollow Glass Microspheres Filled Jute Woven Comingled Composites
- Energy Absorption Mechanism of Thermoplastic Fiber-Reinforced Plastics under Impact Loading Using Split-Hopkinson Pressure-Bar Method
- Effect of Raw Materials on Properties of Coated Al2O3-Al Cermet Materials via Vacuum Sintering Method
- Mechanical Enhancement and Thermal Stability of Composites between Polyamide 11 and Functionalized Graphene Nanoplatelets
- Visualization and Quantification of Stresses at the Ends of Short Fibers Embedded in Epoxy Resin
- Fabrication and Experimental Investigation on Tensile and Flexural Properties for Different Stacking Sequence of Jute and Carbon Fiber Reinforced Epoxy Composite
- Effect of Impregnation Process Parameters on the Mechanical Properties of Carbon Fabric Reinforced Thermoplastic Composites
- Effect of Lamination Direction on the AE Behavior of 3D Printed Specimen during Tensile Testing
- Notch Sensitivity on Fatigue Behavior of Carbon-Carbon Composites
- Observation of Tribological Wear on PEEK Shaft with Artificial Defect under Radial Rolling Sliding Point Contact
- Internal Shear Stress Distribution and Subsurface Cracks of PPS Thrust Bearings under Rolling Contact Fatigue in Water
- Chapter 3: Functional Materials
- Application of Photocatalytic and Adsorption Process for Residue Organic Degradation Using Doped ZnO Composites Hydrogel Beads
- Effect of Ag/ZnO-Graphitic Carbon Nitride on Antimicrobial Activity under Visible Light
- Synthesis of TiO2 Nanofiber by Solution Blow Spinning (SBS) Method
- Absorption of Water Vapor Using Superabsorbent Polymer Composite Material
- Microwave Absorbance of Double-Layer Laminates of Glass Fiber Composite Containing Carbon Black and Carbon Fiber Composite
- Influence of Lithium Oxide on the Characteristics and Mechanical Property in Willemite Crystal Glazes
- Lightweight Cellular Glass Composite from Eggshell and Glass Cullet Powder for Insulation and Bioactive Glass Applications