Cargando…
Advanced materials engineering and technology iv.
| Clasificación: | Libro Electrónico |
|---|---|
| Formato: | Electrónico eBook |
| Idioma: | Inglés |
| Publicado: |
Pfaffikon :
Trans Tech,
2016.
|
| Colección: | Materials science forum ;
v. 857. |
| Temas: | |
| Acceso en línea: | Texto completo |
Tabla de Contenidos:
- Advanced Materials Engineering and Technology IV
- Preface, Committees
- Table of Contents
- Chapter 1: Materials and Technologies for Soldering and Packaging in Electronics
- Intermetallic Study on the Modified Sn-3.5Ag-1.0Cu-1.0Zn Lead Free Solder
- Solderability and Interfacial Intermetallic Compound (IMC) Growth of Sn-Cu-Ni Solder with Additions of Germanium
- The Effects of Zinc Addition on the Microstructure, Melting Point and Microhardness of Sn-0.7Cu Lead-Free Solder Fabricated via Powder Metallurgy Method
- Properties of Aluminum Matrix Composite (AMCs) for Electronic Packaging
- Effects of Wetting Behavior on Gallium Addition in In-Zn Solder Alloy
- The Alloying and Aging Effects on the Wettability and Intermetallic Bonding of the Sn-Zn-Cu-Bi Soldering Alloy on a Cu Substrate
- Nanoindentation Study on Heat Treated Gold Wire Bonding
- Directional Growth Behaviour of Intermetallic Compound of Sn3.0Ag0.5Cu/ImSn Subjected to Thermal Cycling
- Nanoindentation of Sn3.0Ag0.5Cu/ENIG Solder Joint after High Temperature Storage
- Solidification of Sn-3Ag-0.5Cu and Sn-0.7Cu-0.05Ni Solders
- Effects of Trace Phosphorus in Sn-Cu-Ni Wave Solder Dross
- Suppression of Cu3Sn with Ni in High Cu Containing Sn-Cu Solder Alloys
- Peritectic Reactions and Phase Transformations of Sn-30wt%Cu for High Temperature Pb-Free Soldering Applications
- XPS Analysis of Oxide Films on Lead-Free Solders with Trace Additions of Germanium and Gallium
- Improvement of Sn-0.7Cu Lead Free Solder Joints on Shear Strength with Addition of Titanium Oxide (TiO2) Particles
- Surface Roughness and Wettability of SAC/CNT Lead Free Solder
- Wettability of CNT-Doped Solder under Isothermal Aging
- Mechanical Interlocking on Leadframe Surface for Bondability of Au Wedge Bond
- Ultrasonic Vibration in Leadframe for the Bondability for Au Wedge Bond.
- Wettability of Soldering Alloys at Heating by Electron Beam
- Mechanical and Electrical Properties of Carbon Nanotubes Based Isotropic Conductive Adhesives
- Chapter 2: Materials for Electronics, Optoelectronics and Electrotechnical Industry
- Effect of Loading Amount of Glucose Precursor on Mesoporous Carbon Surface Area for Supercapacitor Electrode Application
- Effect of Al Excess on the Band Structure of ZnO Using Density Functional Theory
- Microwave Irradiation Assisted Synthesis of Silicon Carbide Nanotubes
- Characterization of Silicon Carbide Nanowhiskers Synthesized by Microwave Heating Using Photoluminescence Spectroscopy and Fourier Transform Infrared Spectroscopy
- Synthesis of Silicon Carbide Nanowhiskers from Graphite and Silica of Different Ratio by Microwave Irradiation Assisted Synthesis
- Effect of Stoichiometry and Sintering Temperature on the Mechanical Properties of Zinc Ferrite (ZnxFe3-xO4)
- p-Type Conductivity Control in ZnO Films Grown by Molecular-Beam Epitaxy
- Synthesis and Characterization of Ni0.8Zn0.2Fe2O4 Nanoparticles by Self-Combustion Technique
- Synthesis of Chlorophyll Thin Film from Noni Leaves via Dip Coating Process
- Properties of Y3Fe5O12 (YIG) as Nanocatalyst for Ammonia Formation Produced from Magnetic Induction Method (MIM)
- Response Surface Methodology (RSM) in Fabrication of Nanostructured Silicon
- Chapter 3: Composite and Polymer Materials
- Rigid Polyurethane Foam with Ionic Liquid Modified Multi Walled Carbon Nanotubes Composites
- The Effects of Trans-Polyoctylene Rubber (TOR) on the Cure Characteristics and Swelling Behaviour of Activated Carbon Filled Styrene Butadiene Rubber (SBR) Vulcanizates
- Composite Materials Characterization for Aircraft Application
- The Influence of Blending Methods in Epoxy/PMMA Polymer Blend.
- Development of Seamless Pipe Based on Al/Al2O3 Composite Produced by Stir Casting and Centrifugal Casting
- Effects of Composition and Fe on the Liquid Phase Sintered W-Brass Composites
- Palm Kernel Shell Filled Recycled High-Density Polyethylene: Effect of Filler Loading
- Chapter 4: Materials and Processing Technologies for Mechanical Engineering
- Control of Temperature in Cutting Zone in Machining of Alloyed Case-Hardened Steels by Applying a Ceramic Tool with Wear-Resistant Coatings
- Comparative Evaluation of Properties of Various Tool Materials by Area of Indentation Track in Pendulum Scratch Testing
- Edge Cutting Tools for Machining of Hard-to-Cut Materials
- Specifics of Application of Cutting Ceramics with Functional Coating in Turning of High-Strength Materials
- Influence of Tool Rotational Speed on the Mechanical Properties of Friction Stir Welded Al-Cu-Li Alloy
- Effect of Sensitization Treatment on Corrosion Properties in Austenitic Stainless Steel 304
- Synthesis of Porous Anodic Alumina (PAA) on Aluminum Alloy AA6061 in Mixture of Phosphoric Acid and Oxalic Acid
- The Effect of Sintering Temperature to the Microstructure of PM F75 (Co-Cr-Mo) Alloy
- Two-Step Solution Heat Treatment of AlSiCu Alloy for Improvement of Mechanical Properties
- A New Free-Machining Steel Containing Bismuth and Calcium
- The Effect of Solution Heat Treatment on Incipient Melting of Al2Cu Intermetallic Phase in Lightweight Materials
- Ageing Response of Powder Metallurgy AZ91 and AZ91 Reinforced with Multiwall Carbon Nanotube
- Microstructure and Mechanical Properties of Friction Stir Welded AA2195-T0
- Thermal Aging of Dissimilar-Metal Weld Joints for Reactor Pressurized Vessels at Elevated Temperature
- Microstructural Evolution of Austenitic Stainless Steel AISI304 and AISI316 Subjected to High-Temperature Thermal Aging.
- Effect of Concentration of Oxalic Acid on the Synthesis of Porous Anodic Alumina (PAA) on Aluminum Alloy AA6061
- Segregation Measurement of Inconel 718 Feedstocks Used in Low-Pressure Metal Injection Molding
- Precision Hole Making on Laminates Composite: Comparison between Drilling and Punching
- Chapter 5: Construction Materials
- Dynamic Increase Factor of High Strength Concrete with Silica Fume at High Strain Rate Loading
- Experimental Study on Internal RH of BFS Mortars at Early Age
- Strength of Portland Cement with Several Composition of Bottom Ash in Different Fineness with Curing Time of 28 Days
- The Barriers and Strategies of Implementing the New Building Material (Fibre Cement Wall) in Malaysia Case Study: Aurum Synergy, Perlis, Malaysia
- Dolomite Quarry Waste as Sand Replacement in Sand Brick
- An Experiment on Bond Properties of Reinforcements Embedded in Ultra High Performance Concrete
- Bond-Slip Relation of Pretensioned Concrete Members for Various Tensioning Forces
- Assessment of Reinforced Concrete Building with Soil Structure Interaction Effect under Vertical Earthquake
- The Temperature Effect to the Concrete due to the Single Strike of High Electric Current
- Indoor Air Quality of Fired Clay Brick Incorporated with Mosaic Sludge
- Leachability of Heavy Metals from Steel Mill Sludge Incorporated in Fired Clay Brick
- Leaching of Heavy Metals Using TCLP and SPLP Method from Fired Clay Brick Incorporating with Mosaic Sludge
- Properties of Steel Mill Sludge Waste Incorporated in Fired Clay Brick
- Experimental Study of Slurry Infiltrated Fiber Reinforced Concrete
- The Chemical Composition and Fineness of Natural Cement at Different Raw Meal Proportion
- Effect of Chromium (II, III) Oxide and Cobalt Oxide on the Colour and Fineness of Cement
- Mechanical Properties of Volcanic Ash Based Geopolymer Concrete.
- Potential of Geopolymer Mortar as Concrete Repairing Materials
- Review on Different Types of Geopolymer Concrete Fibres
- Effect of Coal Ash Properties on Compressive Strength of Bottom Ash-Based Geopolymer Concrete
- Microstructure and Mechanical Properties of Ambiently-Cured Blended Coal Ash-Based Geopolymer Concrete
- Effect of NaOH Concentration on Flexural Strength, Phase Formation and Microstructural Development of Kaolin Geopolymer Ceramic
- Effect of Ultra High Molecular Weight Polyethylene (UHMWPE) as Binder and Sintering Temperature in Kaolin Geopolymer Ceramics on Flexural Strength
- The Use of Borax in Deterring Flash Setting of High Calcium Fly Ash Based Geopolymer
- Simulation Behavior of Flexure in Reinforced Concrete Beam with Opening Reinforced with Glass Fiber Reinforced Polymer (GFRP)
- Flexural Behaviour of Patch-Repair Material Made from Unsaturated Polyester Resin (UPR)-Mortar
- Optical Data Support on Flexural Strength of Kaolin Coated Lumber Wood via Geopolymer Technology
- Chapter 6: Biomedical Engineering and Biotechnologies
- Study on a Fractional Model of Filtration Effect of Cigarette Filter Tip
- Preparation and Characterization of Chitosan/Alginate Polyelectrolyte Complex Prepared by Using Calcium Tripolyphosphate Ionic Gelator
- Analysis on Fluid Characteristics in Y-Shape Bifurcate Coronary Artery
- Performance of Newly-Fabricated Modular Surface Plasmon Resonance (mSPR) Sensor
- Simultaneous Saccharification and Co-Fermentation (SSCF) Using Banana and Pineapple Waste as Substrate
- Optimization of Eugenol Ester Using Statistical Approach of Response Surface Methodology
- Facile Synthesis of Activated Carbon from Swamp Taro Stalk via Single Step ZnCl2 Activation
- Synthesis and Characterization of Biomass Supported Ag, Co and Ag-Co Nanoparticles.