Cargando…
Advanced materials and structures V : selected, peer reviewed papers from the Fifth International Conference on Advanced Materials and Structures (AMS 2013), October 24-25, 2013, Timișoara, Romania /
Collection of selected, peer reviewed papers from the the Fifth International Conference on Advanced Materials and Structures (AMS 2013), 24-25 October 2013, Timişoara, Romania. The 56 papers are grouped as follows: Chapter 1: Advanced Materials, Chapter 2: Materials Characterization, Chapter 3: Mo...
| Clasificación: | Libro Electrónico |
|---|---|
| Autor Corporativo: | |
| Otros Autores: | , |
| Formato: | Electrónico Congresos, conferencias eBook |
| Idioma: | Inglés |
| Publicado: |
Pfaffikon, Switzerland ; Enfield, NH :
Trans Tech Publications,
[2014]
|
| Colección: | Diffusion and defect data. Solid state phenomena ;
v. 216. |
| Temas: | |
| Acceso en línea: | Texto completo |
Tabla de Contenidos:
- Advanced Materials and Structures V; Preface, Committees and Sponsor; Table of Contents; Chapter 1: Advanced Materials; About Replacement of Nickel as Amorphization Element for Fabrication of Ultra-Rapidly Solidified Ti-Zr Alloys; The Effect of Mo and Al on the Corrosion Behavior of Titanium and Some of its Alloys for Biomedical Applications; Structural Characteristics of Ductile Iron at Different Rare Earth Contribution from a Magnesium Ferrosilicon Alloy; Correlation between Microstructure and Magnetic Properties on MnZn Ferrite with Bi2O3 Increasing Addition
- Composite Powder and Compacts of Iron/Iron Oxide Type Produced by Mechanosynthesis and Reactive SinteringCrystallization of Ni-Cr-Si-B and Ni-Cr-Fe-Si-B Amorphous Alloys; Implant Surface Finishing Influence on Tissue-Implant Anchoring; Mechanical Behavior of Fe60Co14Ga2P10B5Si3Al3C3 Bulk Metallic Glass; The Influence of Sulphur and Oxigen Additions in Mg-Treated Iron on the Cooling Curves Parameters; Research on the Influence of Pelleting Mixture Components on Chemical Components and Pellets Structure; Chapter 2: Materials Characterization
- Joint Quality Assessment of Three Different Laser Welded Dental AlloysDescription of Degradation Process of Rubberized Lean Concrete; Influence of Cooling Rate on the Structural Characteristics of Ca and Rare Earth Inoculated, Low-S Grey Cast Iron; Influence of the Si-Content on the High Temperature Oxidation Behaviour of NiCrBSi-Coatings; A Study on Metal-Ceramic Thermal Expansion Compatibility; An Evaluation of Sn-Cu-Ga and Sn-Cu-Ag Solder Alloys for Applications within the Electronics Industry
- Analysis of Hazards Identified within the Premises of the Electric Steelworks, to Carry out the Risk AssessmentComputation of HAZ Hardness for Low Alloyed Welded Steels Using Five-Parameter Logistic Function; Damage Detection in Flux Cored Wire Welded Structures by Using Vibration Testing; Determination of Flexural Properties of Rigid PUR Foams Using Digital Image Correlation; Effects of Silicon Carbide Proportion and Artificial Aging Parameters on Microstructure and Hardness of Al-Cu/SiCp Composites
- Experimental and Numerical Investigations of TBC Behaviour after Aging, Subjected to Tension and BendingDetermination of Mechanical Properties of Chondrocytes in Articular Cartilage Using Atomic Force Microscopy; Heat Transfer in Composites Subjected to Temperature Variations; Influence of Milling Time on the Homogeneity of the Al2O3/Ni Composite Powders Obtained by Mechanical Milling; Measurement of Young's Modulus and Shear Modulus of Some Structures Welded Using Flux Cored Wire by Vibration Tests