Cargando…
4th mechanical and manufacturing engineering : selected, peer reviewed papers from the 4th International Conference on Mechanical and Manufacturing Engineering (ICME 2013), December 17-18, 2013, Bangi-Putrajaya, Malaysia /
Collection of selected, peer reviewed papers from the 4th International Conference on Mechanical and Manufacturing Engineering (ICME 2013), December 17-18, 2013, Bangi-Putrajaya, Malaysia. The 260 papers are grouped as follows: Chapter 1: Advanced Mechanical and Manufacturing Design Technology; Chap...
| Clasificación: | Libro Electrónico |
|---|---|
| Autor Corporativo: | |
| Otros Autores: | |
| Formato: | Electrónico Congresos, conferencias eBook |
| Idioma: | Inglés |
| Publicado: |
Zurich, Switzerland :
Trans Tech Publications,
[2014]
|
| Colección: | Applied mechanics and materials ;
v. 465-466. |
| Temas: | |
| Acceso en línea: | Texto completo |
Tabla de Contenidos:
- 4th Mechanical and Manufacturing Engineering; Preface, Foreword and Committees; Table of Contents; Chapter 1: Advanced Mechanical and Manufacturing Design Technology; Nonlinear System Identification of Floating Structures Using Time-Varying ARX-Based Volterra Model; Fabrication Process of Polymer Nano-Composite Filament for Fused Deposition Modeling; Railway Dynamics Analysis Using Lego Mindstorms; Design and Enhancement of Radiofrequency Cannula (RC) for Chronic Pain Management; Topology Optimization of Beam Structures with Various End and Loading Conditions
- Short Review: Role of Metal Oxides as Filler in Polysiloxane Sheet CompositeOccupant Kinematic Study in Safe Bus Superstructure; A Novel Design of Car Wiper Using Compliant Mechanism Method; CFD Application in Resistance Analysis for Advanced Semi-SWATH Vehicle; Thermo-Mechanical Stress Analysis in Electronic Packaging with Continuous and Partial Bond Layer; Evaluation of FDM Pattern with ABS and PLA Material; Ergonomic Design of CNC Milling Machine for Safe Working Posture; Micro-Scale Abrasion of WC-Based Coatings with Different Abrasive Type
- Magnesite Effect to the Alumina Sintering for Heat Sink ApplicationSintering of Alumina-AIN System for Heat Sink; Gravity Effects on the Density of Laminated Composite due to the Differences in Angle Cured; Water Absorption and Thickness Swelling of Laminated Composite after Cured at Different Angle; Simulation of Ironing Process for Earring Reduction in Sheet Metal Forming; Dimensional Accuracy Evaluation of Rapid Prototyping Fused Deposition Modeling Process of FDM200mc Machine on Basic Engineering Profiles
- Tensile Properties of Angle Cured Laminated Composites Structures under Gravity EffectsChapter 2: Alternative Energy and Green Energy; CFD Analysis of Circle Grid Fractal Plate Thickness on Turbulent Swirling Flow; Steady
- State Potential Energy Recovery Modeling of an Open Cathode PEM Fuel Cell Vehicle; Techno-Economic Analysis of an Alkali Catalyzed Biodiesel Production Using Waste Palm Oil; Mono-Gas Fuelled Engine Performance and Emissions Simulation Using GT-Power; Influence of 1-Butanol Additives on Palm Biodiesel Fuel Characteristics and Low Temperature Flow Properties
- Characterization of Blended Biodiesel Fuel Properties with Small Portion of Butanol as a Fuel AdditiveExergy Analysis of a Micro-Gas Turbine Fueled with Syngas; Unsteady Magnetohydrodynamic Free Convection Flow of a Radiative Fluid Past an Infinite Vertical Plate with Constant Heat and Mass Flux; Investigation of Evacuated Tube Collector Performance at High Temperature Mode Using TRNSYS Simulation Model; The Comparison of Preheat Fuel Characteristics of Biodiesel and Straight Vegetable Oil; Effects of Calcination Factors on the Composite Cathode Powder LSCF-SDC Carbonate by Using Dry Milling