Cargando…

Frontier in functional manufacturing technologies : selected, peer reviewed papers from the 2nd International Conference on Functional Manufacturing Technologies (ICFMT 2010), Aug. 6-9 2010, Harbin, Heilongjiang, China /

The major topics covered by the special volumes include anti-fatigue design and anti-fatigue manufacturing, manufacturing systems and reliability, processing detection and monitoring-control, CIMS and management systems, production system and simulation technology, quality control of manufacturing s...

Descripción completa

Detalles Bibliográficos
Clasificación:Libro Electrónico
Autor Corporativo: International Conference on Functional Manufacturing Technologies Harbin, China
Otros Autores: Zuo, Dunwen
Formato: Electrónico Congresos, conferencias eBook
Idioma:Inglés
Publicado: Stafa-Zurich, Switzerland : Trans Tech Publications, ©2010.
Colección:Advanced materials research ; v. 136.
Temas:
Acceso en línea:Texto completo
Tabla de Contenidos:
  • Preface
  • Effect of Rare Earth Ce on Casting Properties of Al-4.5Cu Alloy
  • Simulation and Experimental Investigations of Fiber Diameter of Spunbonding Nonwovens by Means of the Air Jet Flow Field Model
  • Numerical Simulation of Accumulative Forming Bipolar Plates of Fuel Cell
  • Low Temperature Synthesis and Luminescent Properties of Ca₂SnO₄: Eu³
  • Study on Load-Velocity Dynamic Property of Piston-Type Hydraulic Cylinder Based on SIMULINK
  • Study on Formability about ME20M Magnesium Alloy Sheet
  • Effect of Adding Er on Interfacial Reactions between Sn-3.0Ag-0.5Cu Solder and Cu Substrate
  • Ocular Aberrations Measurement Combined with Subjective Visual Compensation
  • Analysis of the Milling Distortion Due to Residual Stress Based on FEM
  • Research of Thermodynamics and Properties of Pb/WC-Zro₂ Inert Electrodes Used in Zinc Electrodeposition
  • Study on Influence Scope of Shock Wave and Smoke Flow after Gas Explosion
  • Fabrication of Biodegradable Polymeric Micro-Analytical Devices Using a Laser Direct Writing Method
  • Research on Fabricating Technology of Three Dimensional Integrated Braided Composite I Beam
  • Simulated Annealing Genetic Algorithm and its Application in Mixed-Model Assembly Line Design
  • Construction of Marketing Management Information System of Travel Agency Based on Customer Relationship Management
  • Research on the Application of Fuzzy Neural Network in the Automobile Reliability
  • A Multi Agent-Based Approach for Supply Chain Network
  • Experiment Research of Cutter Edge and Cutting Parameters Influence on Machined Surface Roughness for High Speed Milling Hardened Steel
  • Study on Laser Triangulation Measurement Principle of Three Dimensional Surface Roughness
  • Estimation and Display of Triangular Mesh Curvature in Reverse Engineering
  • The Optimization for Design of the Parameters of Spiral Baffle
  • Feature Analysis for Milling Force of Three-Edge End Mills
  • The Reliability Analysis of a Vacuum Forming Mold for IC Packing Bag
  • A Non-Linear Flow Channel Implementation Method in Magnetic Gap Space of Magneto-Rheological Valve
  • The Analysis of Key Influence Factors and Application Countermeasures on Quality of FDM Prototype Model
  • Calculation Method for the Profile Curves of Cycloidal Pump
  • Effect of Alkaline Treatment of Wood Flour on Strength of Wood-Plastic Composites for Selective Laser Sintering
  • Application of Regression Analysis of Reliability Research in Off-Center Wearing on Well Tube and Rod of Oil Sucker
  • A Modified Wavelet Transform Profilometry
  • Simulation Study on Deep Hole Drilling Machine Hydraulic System Based on System Schematic Diagram
  • Study on the Green Processing of Impeller
  • Development of a Ring Permeability Test System
  • The Variable Non-Linear Flow Channel Method and Device
  • Research on Bearing Life Prediction Based on Three Parameters Weibull Distribution
  • The Study of Target Points Center Extracting and Matching in Calibration
  • The Prediction of Shot Peening's Surface Roughness with Premixed Water Jet Based on Neural Network
  • Research on Safety Protection Technology of Conventional Lathe CA6140
  • Preparation and Properties of Waterborne Polyurethane with PDMS Side Chain
  • Investigation of the Drawing Process of a Square Rod from a Round Bar by Using 3-D Finite Element Analysis
  • Finite Element Numerical Simulation of EDM Surface Strengthening in Gas Medium of Stainless Steel 1Cr13
  • The Application and Development of Microbubble Column Flotation Technology in China
  • Effects of Isothermal Process Parameters on the Microstructure of Semisolid Alsi7mg Alloy Produced by EPM
  • Study on Dynamic Fuzzy Classification of Design Proposal Based on Design Style
  • Analytical Study on Kinetic Characteristic of the Shell of Air-Powered Diving Pump
  • Study on Variant Design and Improving Technology of Complex Mechanical Products Based on Knowledge Reuse
  • Study of Modeling and Distortion Predicting for Multi-Frame Components
  • The Development of Fault Diagnosis System of Reciprocating Compressor Based on LabVIEW
  • The Dynamic Finite Element Analysis of Table of VM1000 CNC Machining Center
  • Integration Technology and Application Research on Management Information in Textile Industry
  • Flexible Wedge-Effect for Insect Flying and Fishtail-Effect for Fish Swimming
  • Study on Cumulate Function of Cut-In Impacting Disrepair with Waved-Edge Milling Insert
  • Preparation of V-Doped Titanium-Bearing Blast Furnace Slag and its Antibacterial Activity to Mildew
  • Study on Temperature Field of Different Substrate Shape in Preparing Diamond Film
  • Research on Fatigue Behaviors of Nodular Cast Iron QT800 by Laser Shock Processing
  • Numerical Simulation of Thermal Deformation of High Speed and Exactitude Thermo Grip
  • FTA-BN Approach to Risk Assessment of Die Casting Die and Risk Mitigation Solution in 4Ps Development Framework
  • Study on Atmospheric Corrosion Behaviour of Sicp/Al Composite
  • Experiment Research on Grinding of Optical Glass with Indigenously Developed Monolayer Brazed Diamond Grinding Wheel
  • Open CNC System Based on Embedded Monitoring Unit
  • Study on Adsorption Characteristics of Ni (II) by Palygorskite
  • Experimental Study on Thermostatic Cutting Nickel-Base Superalloy GH4169
  • Research on RFID and Vision-Based AGV Navigation
  • Study on Data Acquisition System for Cold Extrusion of Internal Threads Based on Virtual Instrument
  • The Influence of Surface Tension on Lubrication Film Thickness and Pressure
  • New Technology of Solospun and Prospect of its Application and Development
  • Study of Traction Properties of Three Space Lubricants Used for Rolling Bearing.