Cargando…
Advances in Materials and Materials Processing V /
Collection of selected, peer reviewed papers from the 2014 5th International Conference on Advances in Materials and Manufacturing (ICAMMP 2014), December 20-21, 2014,Fuzhou, China. The 192 papers are grouped as follows: Chapter 1: Composites; Chapter 2: Low-dimensional and Nano-Materials; Chapter 3...
| Clasificación: | Libro Electrónico |
|---|---|
| Autor Corporativo: | |
| Otros Autores: | , |
| Formato: | Electrónico Congresos, conferencias eBook |
| Idioma: | Inglés |
| Publicado: |
Zurich :
Trans Tech Publishers,
©2015.
|
| Colección: | Advanced materials research ;
v. 1095. |
| Temas: | |
| Acceso en línea: | Texto completo |
Tabla de Contenidos:
- Advances in Materials and Materials Processing V; Preface and Committee; Table of Contents; Chapter 1: Composites; Analysis of the Geometry and Microcracks of Kevlar/Epoxy Composites; Effect of Diamond Shape on Surface Roughness of Diamond/Cu Composites; Effect of Diamond Shape on Thermal-Physical Properties of Diamond/Cu Composites; Effects of Sintering Temperature on Microstructure and Wear Properties of Al2O3 Particle Reinforced Al Composites; Preparation of Nickel-Based Al2O3-TiB2 Composite Ceramic Powder.
- Experimental Study on the Effect of Retained Austenite on the Impact Toughness of a Low-Carbon Martensite Steel; Galvanic Corrosion of 70-30 Copper-Nickel Alloy in Contact with Nickel-Aluminum Bronze in Simulated Deep Sea Environment; High Temperature Oxidation Investigation of Hot Roll Material with High-Speed Steel; Influence of Neodymium on Wear Resistance of Hypereutectic Al-Si Alloy; Influence of Pre-Deformation Strain on Recovery Performance of Ni47Ti44Nb9 Alloy [Phi]8mm Pipe Joint.
- The Influence of Sintering Temperature and Whisker Content on the Flexural Strength of Aluminum Borate Whisker Reinforced Aluminum Phosphate Composite Materials; The Study of Composite Material of Al-C System; Chapter 2: Low-Dimensional and Nano-Materials; Atomistic Simulation on Buckling Behavior of Monolayer Graphene; Modeling and Simulation for Current-Illumination Characteristics of Carbon Nanotube; Preparation and Thermal Fatigue Behaviors of Silicon Nitride Nano-Ceramics; Study on Dispersion and Rheology of Particles in Water-Based Nano TiN Fluid.
- Transmission Performance of Water-Based Nano Fluid Based on Computational Fluid Dynamics; [Beta]-Cyclodextrin Modified Hybrid Magnetic Nanoparticles as an Adsorbent for Phenol Removal; The Preparation of ZrO2 and the Influence of the Calcination Temperature; The Synthesis of Single-Crystal BiOI Nanoplates with {001} Facets Exposed; Chapter 3: Metal-Based Materials and Alloys; A Study on Mechanical and Fatigue Properties of a Stainless Steel; Development of 590MPa Grade Hot-Dip Galvannealed DP Steels; Effect of Annealing Temperature on Microstructure and Damping Capacity of Twin Roll Cast ZK60 Alloy.
- Effect of Ca and Nd Alloying on the Microstructure of Mg-6Al-Ca-Nd Alloy; Effect of Cu on the Electrochemical Corrosion Behavior of Sn-8Zn-3Bi Lead-Free Solder Alloy; Effect of Electropulsing Rolling on the Microstructure and Properties of Industrial Pure Titanium TA1; Effect of Er on Microstructure and Hardness of Al-Zn-In Alloy; Effect of Grain Size on Microstructure and Orientation of Fe-25Mn-3Si-3Al Steel; Effect of Nd on Primary Silicon and Mechanical Properties of Hypereutectic Al-17.5%Si Alloy; Experiment and Analyses on 16 Mn Steel under Cyclic Loading Controlled by Strain.