Cargando…
Materials science and technology : selected, peer reviewed papers from the 2014 2nd International Conference on Advances in Materials Science and Engineering (AMSE 2014), October 1-2, 2014, Dubai, UAE /
Collection of selected, peer reviewed papers from the 2014 2 nd International Conference on Advances in Materials Science and Engineering (AMSE 2014), October 1-2, 2014, Dubai, UAE. The 37 papers are grouped as follows: Chapter 1: Materials Science and Technology; Chapter 2: Applied Mechanics; Chapt...
| Clasificación: | Libro Electrónico |
|---|---|
| Autor Corporativo: | |
| Otros Autores: | , |
| Formato: | Electrónico Congresos, conferencias eBook |
| Idioma: | Inglés |
| Publicado: |
Zurich, Switzerland :
Trans Tech Publications,
2015.
|
| Colección: | Advanced materials research ;
v. 1064. |
| Temas: | |
| Acceso en línea: | Texto completo |
Tabla de Contenidos:
- Materials Science and Technology; Preface and Organizing Committee; Table of Contents; Chapter 1: Materials Science and Technology; Deterioration of Mortar Composites in Acidic Environment; Evaluation of Friction Coefficient by Ring Compression of Magnesium Alloys; Preservation of Archaeological Leather by Reinforcement with Styrene Butadiene Rubber; Amine-Functionalized Graphene for Natural Gas Sweetening; High Strength and Ductility in Multi-Directional Forged Wrought Aluminum Alloys.
- Effect of Sintering Time on the Density, Porosity Content and Microstructure of Copper
- 1 wt. % Silicon Carbide CompositesInvestigation of Non-Monotonic Portions on the Temperature Dependences of High-Temperature Metal Melts' Physical Properties; Non-Destructive Testing for the Evaluation of Pozzolanic Mortar Reinforced to Corrosion; The Abnormal Grain Growth of P/M Nickel-Base Superalloy: Strain Storage and CSL Boundaries; Main Clay Minerals and their Microscopic Morphological Characteristics in Zhangcun Illite Ores.
- High-Temperature Synthesis of Composite Material from Al-SiO2 System ComponentsThe Synthesis of TiC Powders by Carbothermal Reduction Method in Vacuum; Investigation on the Continuous Microwave Synthesis of Nano Titanium Carbide Powder; Oxidation of Cyclohexene over Mesoporous Silica Pillared Clay Incorporated with Heteropoly Acid Prepared by Sol Gel Method; 2D Woven Reinforcements of Natural Fibers; Effect of the Nature of the Layer of Conductive Polymer Composite on the Effectiveness of a Multi-Layer Electromagnetic Shielding.
- Synthesis of a Novel Structure Carbon Nanocoils and their Application in Photo Diode DevicesShrinkage Behavior of Composite Geopolymer Mortar Cured at Different Relative Humidities; Chapter 2: Applied Mechanics; Vibromechanic Way to Remove Residual Stresses; Fatigue Life Prediction of Composite Laminates Based on Progressive Damage Analysis; Research on Calculation of Equivalent Damping Ratio of Electrical Transmission Tower-Line System with Viscoelastic Dampers; The Impact of Pre-Heating on Pressure Behavior in Tapered Cylindrical Die in Pultrusion of Large-Sized Composite Rods.
- Chapter 3: Materials Processing and Manufacturing, Coating EngineeringInfluence of Stacking Fault Energy on the Grain Size of FCC Metals Fabricated by Accumulative Roll Bonding Process; Blast-Hole Cuttings Grindability Relationship with Silica Content and Bit Wear Rate; Surface Modification of Broaches from the Powder High Speed Steels Applied to Processing of Aviation Products from Heat-Resistant Alloys; High-Strength Ceramic Cutting Tools with Multipurpose Coatings for Highly Effective Processing of Tempered Steel; Options for Forming of Nanostructured Surface Coatings.