Cargando…

Tribology in manufacturing processes and joining by plastic deformation : selected, peer reviewed papers from the 6th International Conference on Tribology in Manufacturing Processes & Joining by Plastic Deformation, June 22-24, 2014, Darmstadt, Germany /

Collection of selected, peer reviewed papers from the 6th International Conference on Tribology in Manufacturing Processes & Joining by Plastic Deformation, June 22-24, 2014, Darmstadt, Germany. The 63 papers are grouped as follows: Chapter 1: Plenary Keynotes, Chapter 2: Wear and Friction Testi...

Descripción completa

Detalles Bibliográficos
Clasificación:Libro Electrónico
Autor Corporativo: International Conference on Tribology in Manufacturing Processes & Joining by Plastic Deformation Darmstadt, Germany
Otros Autores: Groche, Peter (Editor )
Formato: Electrónico Congresos, conferencias eBook
Idioma:Inglés
Publicado: Zurich, Switzerland : Trans Tech Publications, [2014]
Colección:Advanced materials research ; v. 966-967.
Temas:
Acceso en línea:Texto completo
Tabla de Contenidos:
  • Tribology in Manufacturing Processes & Joining by Plastic Deformation; Preface and Scientific Committee; Table of Contents; Chapter 1: Plenary Keynotes; Off-Line Testing of Tribo-Systems for Sheet Metal Forming Production; Combination of Plastic Upsetting Joining and Plastic Serration Joining of Disk and Shaft; Joining Processes by Plastic Deformation; Two-Dimensional Roll Bite Model with Lubrication for Cold Strip Rolling; Chapter 2: Wear and Friction Testing; Friction Measurement Device for Fiber Material Forming Processes
  • Influences of Cobalt Content on the Physical and Tribological Properties of Cemented Tungsten Carbide Used in Sheet Metal Forming ApplicationDevelopment of a Heating System for a Spiral Tribometer to Investigate the Influence of Temperature on Tribological Systems; The Influence of Initial Commutator Surface Roughness on Wear of the Starter Motor Commutation System; A Wear Damage Assessment of High Temperature Forging Tool; Surface Textures and Friction Control in Microforming; Identification of Local Lubrication Regimes on Textured Surfaces by 3D Roughness Curvature Radius
  • Chapter 3: Machining OperationsEffects of External Hydrostatic Pressure on Finished Surface in Silicon Cutting; Investigating the Effect of Ultrasonic Vibration on Hole Accuracy in Drilling of Metal Matrix Composites; Micro Dimple Milling for Structured Surface; Topographic Wear Monitoring of the Interface Tool/Workpiece in Milling AISI H13 Steel; Evolution of Dynamic Recrystallization of AISI-1045 Steel under Critical Friction Conditions; Mutual Effect of Groove Size and Anisotropy of Cylinder Liner Honed Textures on Engine Performances
  • The Role of Tool Geometry and Process Parameters during Fly Shearing in Hot Rolling of SteelRheological Investigation of MIM Feedstocks for Reducing Frictional Effects during Injection Moulding; Chapter 4: Sheet Forming; Wear Behaviour of Al-Si and Zn Coated 22MnB5 in Hot Stamping; Lubricant Film Breakdown and Material Pick-Up in Sheet Forming of Advanced High Strength Steels and Stainless Steels when Using Environmental Friendly Lubricants; Micro-Plasto-Hydrodynamic Lubrication a Fundamental Mechanism in Cold Rolling
  • Direct Evaluation of Coulomb Friction Coefficient from Sheet Strip Stretch Test on a Cylinder SurfaceInfluence of Tool Steel Hard Phase Orientation and Shape on Galling; Characterisation of Tool Coatings for Press Hardening; Experimental and Numerical Investigations on Frictional Behaviour under Consideration of Varying Tribological Conditions; Chapter 5: Massive Forming; Development of Upsetting-Extrusion Type Tribometer for Evaluating Lubrication Coating Performance in Cold Forging; Enhancement of Tribological Performance via Innovative Tooling Design for Extrusion Processes